Texas Refinery Corp
At Peak 8 Solutions, we work directly with you to provide the right, top-quality products to meet your service needs. Our partnership with Texas Refinery Corp (TRC) enables us to provide the best high-end lubricants available today.
With access to a vast selection of high-quality lubricants from TRC, Peak 8 Solutions delivers premium lubricant solutions for all your equipment and machinery. Our services enhance our customers’ maintenance efforts, helping them reduce overall procurement costs while saving time and money.
Just a few examples of TRC lubricants.
- The only grease that leads the market in all four major categories of water resistance, extreme pressure, anti-wear and temperature dropping point.
- Save money by getting longer life out of your pins, bushings and bearings.
- Get the ultimate in resistance to moisture, keeping surfaces free from rusting, pitting and corrosion.
- Get extreme temperature protection with a dropping point of 630 degrees F, far above average dropping points of 290 and 390 degrees F.
- Specially developed high-impact resistant supplements resist severe and continuous impact.
- It will have up to 3 times the life of most name brand greases.
- This lubricant contains high lubricity additives that create more horsepower and better fuel economy while extending particulate filter life and decreasing regeneration cycles.
- Tested #1 on the High-Frequency Reciprocating Rig (HFRR) testing as the best lubrication and wear-reduction fuel additive.
- Offsets the negative effects of biodiesel and increases fuel life by a minimum of 50 percent.
- Provides exceptional cleaning power proven to remove internal diesel injector deposits.
- Contains the most rust inhibitors on the market to prevent premature rusting in tanks, fuel lines and fuel pumps.
- Increases fuel economy by 3-5 percent.
- Reduces negative effects of water contamination.
- Adds life and stability to fuel.
- Reduces fuel system clogging.
- Reduces gum and varnish build-up, and burns fuel efficiently for a noticeable improvement in fuel mileage. Formulation retards wax formation and lowers cloud point by a minimum of 25 degrees.
- It will add life to your VGT Turbo by keeping the "Vanes" lubricated and free of soot.
- Eliminates defoamer — The NF in Hydrate Plus NF means non-foaming. Defoamers can be expensive. Eliminating this ingredient saves money and time.
- Increase the efficacy of agrochemicals — The non-ionic surfactant is not affected by the chemical bond between two oppositely charged ions while providing uniform application.
- Aids drift control — Generally needed with thinner surfactants, Hydrate Plus NF feels heavier and slicker than other surfactants. When mixed with other chemicals, droplets will be denser, causing them to fall faster and be less likely to be affected by light winds—even in aerial applications.
- Economical solutions — Hydrate Plus NF has an economical treatment ratio of 1:800 (1 plant per 100 acres is typical) or 1:400 (1 quart per 100 acres for increased drift or hard-to-kill weeds.
- Acts as a cleaning aid — Hydrate Plus NF reduces salt and mineral deposits to keep your tank, nozzles, and pumps clean, clear and spraying properly.
- Reduces crop oil/MSO dependency — Crop oils or Methylated Seed Oil (MSO) derived from mineral oil or plant seed oils are typically less effective when compared to surfactants. Oils are normally recommended on chemical labels used as a surfactant or “sticker/spreader.” Hydrate Plus NF enhances the chemicals it is mixed with to completely sheet across a plant and provide chemical penetration.
- Reduce reliance on Ammonium Sulfate (AMS) — When using AMS with your chemical mixture, know whether the AMS is for use as a water conditioner, surfactant, or a nitrogen source. Hydrate Plus NF improves results in spray-mixture effectiveness in hard water areas. When used as a surfactant, Hydrate Plus NF shows marked improvement in faster penetration, quicker kill, and consistent coverage. It is rainproof in about two hours. Where AMS is needed to treat water, or as a nitrogen source, Hydrate Plus NF is compatible with AMS and can improve the overall results of the chemical application.
- Use AMS for Round-Up-type chemicals — Notice faster, longer kill rates with herbicides and better coverage with fungicides and pesticides.
